This post’s conclusions are odd. It has a bunch of extensive benchmarks showing that zstd is by far the worst performing across every metric except a slight increase in compression ratio and then says the conclusion is zstd is the best choice. Unless I’m missing something in the data.
In the first benchmark it gets a ratio of 4 instead of 2.7, fitting 36-40% more data with 75% more CPU. It looks great.
The next two show it fitting 20% more data with 2-3x the CPU, which is a tougher tradeoff but still useful in a lot of situations.
The rest of the post analyzes the CPU cost in more detail, so yeah it's worse in every subcategory of that. But the increase in compression ratio is quite valuable. The conclusion says it "provides the highest compression ratio while still maintaining acceptable speeds" and that's correct. If you care about compression ratio, strongly consider zstd.
but for vps, where the cpu usage is extremely low and ram is expensive, it might make sense to sacrifice a little performance for more db cache maybe. can't say without more context
It's only an alternative if you have a backing swap device. zram does not have this requirement, so (aside from using no compression) it's basically the only solution for some scenarios (e.g. using entire disk(s) for ZFS).
This seems like a great place to ask: how does one go about optimizing something like zram, which has a tremendous number of parameters [1]?
I had considered some kind of test where each parameter is perturbed a bit in sequence, so that you get an estimate of a point partial derivative. You would then do an iterative hill climb. That probably won't work well in my case since the devices I'm optimizing have too much variance to give a clear signal on benchmarks of a reasonable duration.
Compression factor tends to stay above 3.0. At very little cost I more than doubled my effective system memory. If an individual workload uses a significant fraction of system memory at once complications may arise.
a comment here about zram caught my eye a day or two ago and I've been meaning to look into it. Glad to see this post (and I'm sure many others saw the same comment and shared my obsession)
Inside the pods it makes no sense, but I do enable it on some memory-constrained worker nodes. Note that the kubelet by default refuses to start if the machine has any swap at all.
As all tradeoffs it depends on your requirements. lz4 is ridiculously fast so it essentially gets you more ram for free, zstd is a lot more CPU-intensive but also has a much higher compression ratio. So if your RAM is severely undersized for some of your workloads and / or you're not especially CPU-bound until disk swap takes you out, then zstd gives you a lot more headroom.
This post’s conclusions are odd. It has a bunch of extensive benchmarks showing that zstd is by far the worst performing across every metric except a slight increase in compression ratio and then says the conclusion is zstd is the best choice. Unless I’m missing something in the data.
In the first benchmark it gets a ratio of 4 instead of 2.7, fitting 36-40% more data with 75% more CPU. It looks great.
The next two show it fitting 20% more data with 2-3x the CPU, which is a tougher tradeoff but still useful in a lot of situations.
The rest of the post analyzes the CPU cost in more detail, so yeah it's worse in every subcategory of that. But the increase in compression ratio is quite valuable. The conclusion says it "provides the highest compression ratio while still maintaining acceptable speeds" and that's correct. If you care about compression ratio, strongly consider zstd.
I have had similar experience, with ZFS zstd dropped IOPs and throughput by 2-4x compared to lz4! On a 64 core Milan server chip…
ZFS lz4 in my experience is faster in every metric than no compression.
the context is missing.
but for vps, where the cpu usage is extremely low and ram is expensive, it might make sense to sacrifice a little performance for more db cache maybe. can't say without more context
An alternative is zswap https://old.reddit.com/r/linux/comments/11dkhz7/zswap_vs_zra... which I believe, despite the name, can also compress RAM without hitting disk.
It's only an alternative if you have a backing swap device. zram does not have this requirement, so (aside from using no compression) it's basically the only solution for some scenarios (e.g. using entire disk(s) for ZFS).
Can't you use a ramdisk as your backing swap device?
Using a ramdisk for zswap is basically just zram with extra steps.
It is not the same at all. The swapping algorithm can make a big difference in performance, for better or worse depending on workload
Zram is just swap but in RAM. It uses the same algorithms as normal swap
Extra steps are fine if the result works better.
If you use hibernation, I think it also compresses your RAM image for potentially less wear and faster loading/saving
why hibernation would not compress to begin with? you're more likely just end up running zstd twice.
Swap isn't compressed by default, hibernation dumps memory to swap
Hibernation uses compression regardless of zswap
Thanks for the correction
This seems like a great place to ask: how does one go about optimizing something like zram, which has a tremendous number of parameters [1]?
I had considered some kind of test where each parameter is perturbed a bit in sequence, so that you get an estimate of a point partial derivative. You would then do an iterative hill climb. That probably won't work well in my case since the devices I'm optimizing have too much variance to give a clear signal on benchmarks of a reasonable duration.
[1] https://docs.kernel.org/admin-guide/sysctl/vm.html
optuna, probably coupled with a VM to automate testing
zram tends to change the calculus of how to setup the memory behavior of your kernel.
On a system with integrated graphics and 8 (16 logical) cores and 32 GB of system memory I achieve what appears to be optimal performance using:
Compression factor tends to stay above 3.0. At very little cost I more than doubled my effective system memory. If an individual workload uses a significant fraction of system memory at once complications may arise.Just I was trying to find a benchmark about this, I wondered which algorithm would work best for videogames. Thanks!
Video games and compute heavy tasks cannot have a large compression factor. The good thing is that you can test your own setup using zramctl.
a comment here about zram caught my eye a day or two ago and I've been meaning to look into it. Glad to see this post (and I'm sure many others saw the same comment and shared my obsession)
You saw a comment a day or two ago about zram, but never got around to looking into it more even though you are obsessed by it?
Has anyone tried using zram inside of various K8s pods? If so, I'd be interested in knowing the outcome.
Inside the pods it makes no sense, but I do enable it on some memory-constrained worker nodes. Note that the kubelet by default refuses to start if the machine has any swap at all.
LZ4 looks like the sweet spot to me, you get OK compression and the performance hit is minimal.
As all tradeoffs it depends on your requirements. lz4 is ridiculously fast so it essentially gets you more ram for free, zstd is a lot more CPU-intensive but also has a much higher compression ratio. So if your RAM is severely undersized for some of your workloads and / or you're not especially CPU-bound until disk swap takes you out, then zstd gives you a lot more headroom.
[dead]